Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

Reducing the unevenness of twist on the vts-08

Issuing time:2023-10-11 11:00

The VTS-08 fold twist produced by Volkmann)   is the most used in the wool spinning industry. Compared with the domestic ring ingot twist machine, it has the following characteristics:

(1) ingot turn a week, yarn twist twice, making the output of the same ingot speed;

(2) due to the use of steel collar and wire hook, the twist machine is easy to apply the strengthening twist, the highest twist can reach 2799 twist / m, while the domestic twist machine only reaches 1260 twist / m; TFO Twisting machinery parts VTS08/09

(3) large coil, less joints and short process, which greatly improves the labor efficiency. However, there are also two prominent problems: (1) the power consumption, the oil cost is more expensive; TFO Twisting machinery parts VTS08/09

(2) the yarn twist length is long, more thin sections, the twist back distribution is not uniform, so the uneven rate of the twist wire is larger than the ring ingot twist machine. In view of the first problem, we make an article on the setting number of ssm and high-speed parallel machine, minimize the difference between the parallel line, and adjust the correction value, so as to shorten the batch time and achieve the purpose of power saving. Tension Bullet TFO Twisting machinery parts VTS08/09So how to reduce the twist asymmetry rate of the double twist machine? As we all know, the twist length of yarn has a great impact on the uniformity rate of twist, that is, the short twist of the twist length is uniform, while the long twist length of the twist is not uniform. Because the twist length of the twist machine is longer than that of the ring ingot twist machine, and because of the winding speed of the winding, the twist asymmetry of the twist line of the twist machine is larger than that of the ring ingot twist line. In order to reduce the twist asymmetry of twist, we studied from the following aspects:

1 Storage yarn quantityTFO Twisting machinery parts VTS08/09

Enough storage of yarn is the premise of the accurate operation of the machine, so the amount of yarn stored on the storage tray is one of the important processes of the machine. When the parallel yarn is a small yarn, we did the following comparative test:





As can be seen from the above table, when the yarn storage amount is greater than or equal to 90 degrees, the twist asymmetry rate is the best.

2 Adjustment of overfeeding enclosure Angle





There is no obvious change in the rate.

3 The use of a rubber washer

The lower end of the spindle wing of the twist machine is equipped with a friction rubber washer (also known as the return machine). It is artificial to make the return machine run on the rubber ring with a certain surface friction coefficient. Will the pad hinder the return of the yarn and affect the twist asymmetry?





The twist asymmetry rate is better than when unnecessary.

4. Air ring pole position






5561 Science and Technology Expo


As can be seen from the above data, when the air coil rod is located at 31 and 32, the air coil is too small, so that the yarn touches the upper edge of the yarn tank, and the yarn is damaged. When the position of the coil rod is 37 and 38, the coil is too large, and the yarn touches the edge of the coil cover, thus affecting the twist to make the asymmetry is large, so the position of the coil rod should be better in 33-36, generally 35 when refueling cup, 33 when not refueling cup, depending on the specific situation.TFO Twisting machinery parts VTS08/09

5 Transmoving guide

The yarn moving on the cross winding device is controlled by the transverse guide, the standard cross Angle is 38 degrees, and the guide hook the closer to the rolling coil the better, but can not touch the rolling part, in the inspection, found that the transverse spindle wing TFO Twisting machinery parts VTS08/09guide and the rolling yarn touch, reflected on the yarn guide, found that the head is white. What way does it affect the twist? We recorded the ingots placed on the rolls one by one, and took 5 of them for testing:





As can be seen from the above table, when the guide hits the roll, the twist is uneven. Therefore, together with the equipment line personnel, according to the requirements, adjust the position of the 5 ingot yarn guide with special tools, so that it will not collide to the roll, and in the position closest to the roll, the results are measured:





From the above data, it can be concluded that whether the transverse moving yarn guide is in the most appropriate position has a certain influence on the twist asymmetry rate. To this end, we require the position of the guide to check one by one before the machine.

6 As we all know, equipment is the basis of quality, and operation is the guarantee of qualityTFO Twisting machinery parts VTS08/09

How to make the equipment and operation more reasonable and ensure the asymmetry of yarn twist, we have done a sets of destructive tests:





It can be seen from the above table that the yarn is not overfed: the bracket is skewed, the brake handles the tray, and the uncoordinated time of the brake tray is the main reason for the uneven twist. The following corrective actions are proposed:

1. The mechanics are required to check the brackets and trays once a week to ensure the smooth transmission;

2. Check the position of the simple tube and the tray, and whether the tray is around the yarn;

3. When running on the tour, check the running condition of the yarn on the super feed Laura. If there is any, take it out for quality inspection.

This year, after continuous testing and improvement of the process parameters of the double twist machine, the twist asymmetry rate has been well controlled, and the product quality has been improved to a certain extent, and the quality of the untwisted yarn has been greatly improved.

Learn the expert tips and tricks to reduce the unevenness of twist on your VTS-08 twisting machine and improve the quality of your TFO twisted machinery parts. Our comprehensive guide covers everythin



Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU