Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

Dry goods丨The most detailed training materials for printing and dyeing factory setting machines, fas

Issuing time:2022-03-09 11:00

Knock on the blackboard to highlight! Focus! The content of the article is comparable to that of the classic setting machine training tutorial. Practitioners read the article carefully


The setting production workshop is a key part of the production process of the paper mill. brush ringThe quality of its processing level immediately threatens the cleanliness of the nylon fabric, the reliability of the large format and the width, and the key safety channel for post-carding processing to improve the use value of the fabric. . Due to the association of the pneumonia epidemic, the lack of order information for paper mills at this stage has resulted in a decrease in operating income! I highly recommend this article and look forward to helping the printing and dyeing company


Styling machine brush 2.png


The purpose and basic principle of the setting machine


Purpose: According to padding various dyes and chemicals to carry out soft, hard, non-slip floor, tenter and epoxy resin carding, etc., to improve the touch, load, color, width, super strength, appearance, etc. of textiles. For non-cotton species, it can also have the effect of stabilizing specifications.

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

Basic principle: The cloth is soaked in the material trough with chemical material, and after brush ringbeing squeezed evenly by the hot-rolled strip, it enters the drying box. When the cloth passes through the drying box, it will be air-dried and set under the effect of high warm air. The cloth after setting has excellent touch and stable specifications.


1. Structural features of the setting machine and the efficacy of each module


Forming machines and equipment; Monforts


Mode MONTEX A 8F double air duct


Speed V=7.5-150m/min


The overall width of the textile is at least 60cm


up to 180cm


Nominal pressure total width B=200cm


Menboshi 6000 type setting machine, drying room Lego building design scheme, compact structure. The aspect ratio of the drying room is 1600MM. The thermal insulation door adopts excellent thermal insulation raw materials and excellent door seal raw materials. The left and right air ducts are set by two DC variable frequency variable speed circulating system centrifugal fans respectively to adjust the exhaust volume, and the total width of the upper and lower air ducts is adjusted according to the width of the processed textiles, which significantly saves resources. This kind of method of adjusting the air volume left and right is especially suitable for processing delicate textiles, plated textiles, satin textiles and the like. The warm air drying room can be equipped with organic waste gas cleaning and easy-going-water direct expansion system software, which can flexibly use the equipment temperature in the whole process of processing to save energy. The environmental humidity of the drying room adopts an excellent electronic computer control system to facilitate environmental protection and energy saving.

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

Setting machine brush cutout.png


The main parameters of the setting processing process include temperature, setting width, falling width, overfeeding, speed per hour, setting secret recipe, working pressure of hot-rolled strip steel in rolling trough, and moisture content of falling cloth.


Basic structure:


The setting machine is mainly composed of five parts, including the feeding part, the weft adjuster, the transmission chain, the drying box and the cloth doffing and rolling equipment. In addition, there are chemical system software and kerosene furnace heating system software.


1. Top up part.


The structure is relatively simple, consisting of a trough and hot-rolled strip steel. The cloth is fed into the trough body to carry chemical material, and then the unnecessary chemical material is squeezed cleanly through the hot-rolled strip. Therefore, the chemical material carried by the cloth is very uniform, which is a prerequisite for obtaining high-quality shaped cloth.


What should be paid attention to here is to always pay attention to whether the working pressure of the upper and lower sides of the hot-rolled strip is consistent. Otherwise, the side with low working pressure will be fed more, and the side with too much pressure will be fed less, and the cloth will be inconsistent up and down, etc. product quality problems.


2. Weft adjuster.

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

Mahlo RFMC94H optical weft adjuster is currently equipped on the setting machine. There are four sets of sensors on the Mahlo optical weft adjuster. Each sensor includes two parts: lighting and light sensing, which can be used to produce weft skew according to the photoelectric effect. The posture part adopts the hydraulic transmission system. When the data signal of the weft and oblique dimensions is transmitted to the operating computer motherboard, the operating computer motherboard will send out a command to drive the hydraulic transmission system, so that the curved roller or the straight roller can adjust the relative angle of view, and then can Correct the weft skew. The fact is: when there is a difference between the cloth management center and the two sides, the curved roller will have a posture; and when there is a difference between the left and right sides, the straight roller will have a posture.


3. Part of the drive chain.

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

The tentering of the cloth on the setting machine is caused by the transmission chain. The transmission chain of the setting machine is driven by a high-power motor close to the place where the cloth is dropped. The transmission chain is equipped with a needle plate. When the cloth enters the transmission chain, the brush wheel on the cloth pressing wheel presses the cloth on the needle plate. On the needle, the cloth can enter the drying box under the transmission system of the multi-row transmission chain. The transmission chain of this type of setting machine is different from other setting machines. It can control the pulling of each section of the needle clip to achieve good practical results. However, some setting machines cannot adjust each section of the needle clip. Square or ladder.


4. Dry the cabinet.


The setting machine has eight sets of drying boxes, and the gas is continuously sprayed on the nylon fabric from the tiny pores on the star-shaped jet frame under the propagating effect of the cooling fan (2) of the circulation system. After the warm air touches the wet rag, the temperature drops and the ambient humidity rises, and is discharged from the holes on the star-jet rack, passes through the filter (6), and is heated by the heat exchanger for continuous circulation system application. The brush heat exchanger (8) of the shaping machine is located directly under the filter screen (6), and the selected heat medium is rolling oil. The heat exchanger has many very thin radiators, which can result in a high-efficiency heat exchanger.

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

5. Cloth dropping and rolling equipment.


The setting machine can choose two kinds of cloth feeding methods: fiddling or rolling cloth according to the production and manufacturing. The two methods are all driven by the electric motor to drive the chain. When the cloth rolling method is used, the reliability of the support force of the cloth is relatively high, and the cloth needs to pass over a support force adjustment guide roller controlled by an air pump. The setting machine brush is used to play with the cloth, and the cloth does not need to go through the support force adjustment roller and change to a fixed guide roller.


Proper operation steps of the setting machine


Setting machine feeding standard - feeding

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

1 Preparation before work.

Suzhou Yuedaer Textile Brush,combing brush,Circular brushes,industrial brush,strip brushes

1.1 Thread the guide cloth according to the prescribed route (or check the guide cloth that has been worn).


1.2 Clean the equipment (cloth entry rack and the front side of the equipment), check whether there is any dirt on the needle clips, and sort out the surrounding environment, such as floor cleaning, cloth car remediation, standard cloth pads, rubber box pads, cloth guide hood cloth, etc. .


1.3 According to the processing technology standard, the cloth to be produced is classified, and the cloth with the same processing technology (secret recipe) is processed centrally.


1.4 Check the basic information on the step card and the binning card, and adjust the support force of the cloth feeding, the total width of the weft inspection, the total width of the tenter and the total width of the suction edge according to different types of regulations, and the standard air pressure of the edge suction device is marked. In addition, notify the chemical staff of chemical materials


1.5 Grasp the progress of production and manufacturing according to the plan, and give priority to the production and manufacture of rush goods.


1.6 Check the guide cloth


1.6.1 Strictly distinguish fluorescent and non-fluorescent light guide cloth.


1.6.2 Each technological process should ensure that the guide cloth is detailed, neat, firm, tidy, and wide enough to prevent the whole process from breaking the cloth, tearing the cloth or falling off the needle or causing the processing cloth to be dirty, etc. The guide cloth should be torn out and sewed on the head again. If it needs to be replaced, the team leader should be contacted immediately to replace it, and the relevant records should be made.


1.6 Check the power plug and power socket of the sewing head machine. If there is any damage, immediately notify the team leader to replace it.


2. Workflow.


2.1 Finding cloth: According to the production plan, take the "Post Finishing Process Card" from the main console, according to the license plate number and other information content, find the cloth that must be processed in the area to be processed and placed, and prepare two to three cars in advance; if there is no plan, implement advanced First-out method standard and both color tone and fluorescent gradient standard processing.


2.2 Material preparation: After finding the cloth, notify the required materials for chemical engineering.


2.3 Check the rags.


2.3.1 Check whether the seam head is pulled out according to the requirements in the above process, and carefully check whether the corresponding "After-finishing and processing sub-boxing card" is consistent with the hot-melt label of the first piece of rags; If it meets the requirements, it will be sent to the engine; when the quality of the seam head does not meet the requirements (flat, straight, uniform, firm), the heavy seam should be torn off and submitted to the team leader for confirmation.


2.3.2 If the process flow does not pull out the rags as required, the setting machine brushes are recorded in the wrong item record book, and the total number and specific cloth quantity on the card are also possible to prevent missing processing;


2.3.3 Check whether the cloth has been sampled without seam or cut, so as to avoid problems such as releasing the plane or tearing the cloth;


2.3.4 Check that the front and back sides are appropriate and ensure that the machine is processed in the forward direction.


2.4 Check the quality of nylon fabric.


2.4.1 Check the relevant records of the process flow before checking, if it has been processed or after processing, remind the following common problems.


2.4.2 Measure the width, accurately measure the width of the cloth to be processed, and record it on the "Post Finishing and Processing Boxing Card".


2.4.3 Check the fluorescent light, turn on the fluorescent tube and turn on other lighting fixtures to check the fluorescent light. If the natural lighting effect is too strong, take 10CM from the front and the back of the cloth car up and close to the fluorescent light tube to compare the fluorescent light, and it will be explained from time to time. What's wrong with Laibu.


2.4.4 Check the quality of other nylon fabrics. Before processing, carefully check the several yards of the top layer of the cloth. During processing, other qualities of nylon fabrics are often checked.


2.4.5 Difficulties found in the above inspection, such as non-compliance with the processing technology regulations or previous technological process records in width or other aspects, other product quality problems, etc., shall be notified to the team leader or superiors, and the difficult problems that cannot be dealt with in this process flow Stop processing.


2.4.6 To check the weft and weft condition of the incoming cloth, if necessary, the cloth should be turned over to adjust the position beforehand, so as to facilitate the processing of the equipment.


2.5 Check the processing technology regulations: Check the processing technology regulations in the process flow column or remarks of the "Post-carding step card", and notify the package in advance for the requirements of the specified package.


2.6 Prepare in advance to start.


2.6.1 Tear off the uneven rags (report when everything is torn normally), and use the sewing machine to connect the rags on the upper side of the processing cloth with the guide cloth. When ready, ring the bell and verbally announce that the main gear is activated, and hand over the step card to the main gear.


2.6.2 For the roll-in cloth, firstly make the cloth that rotates the roll by hand to integrate the accelerated motion of the start-stop processing and avoid excessive support force in a short time.


2.7 The whole process inspection and matters.


2.7.1 Pay attention to observe the condition of nylon fabric during the whole process of processing, strictly ensure that the nylon fabric does not need to be shifted into the cloth roller management center, and use the sewing machine to sew the textile section and the middle head and tail of the section, and use the sewing machine to sew the sewing machine hair brush. The head should be vertical and firm, and the front and back sides should not be mistaken (there are unsalted butter pen handwriting for the front face or hot melt logo for the front face), the two ends are aligned without seam, etc., especially when it is not possible to go up and down Sewing reversed. Enables continuous processing of textiles (commonly used seam threads are the same as above). If you find any problems, report them immediately and make a record. In addition, you should also pay attention to the unsalted butter hand mark or hot melt logo at the inspection joint. If the brush of the setting machine is not available, you should notify the team leader to make a supplement and record it.


2.7.2 Check whether there is a sampling staff mark on the sampling connection and the sub-box card according to the regulations, if not, it must be reported to the squad leader or on-site manager and put on record.


2.7.2 Check whether there is a sampling staff mark on the sampling connection and the sub-box card according to the regulations, if not, it must be reported to the squad leader or on-site manager and put on record.


2.8 Next steps.


2.8.1 When processing one car, at least prepare the cloth to be processed in the next car and put it into the cloth car parallel to the processing. When processing at least 500Y up and down, prepare for the next work in advance. If there is cloth on the brush of the setting machine When processing again, it is necessary to prepare cloth, inspect, sew, etc. If there is no cloth that can be processed temporarily, it is necessary to connect the confirmed guide cloth.


2.9 Finished work.


2.9.1 Immediately after the processing of one car of cloth is completed, the empty cloth car (the bad cloth car will be sent to a specific address for maintenance, the old production workshop will be sent to the gate of the equipment maintenance worker, and the new production workshop will be sent to the outside of the material room), and the cloth will be sent to the laying worker. place. After all the work is completed, do a good job in cleaning up, turning off the water, turning off the lights, turning off the electricity, turning off the steam, turning off the gas, and releasing the pressure.


3. Frequently Asked Questions.


3.1 Some unique types are optional for machinery and equipment, and must be carried out according to the processing technology regulations or notices.


3.2 When changing materials and types, be sure to turn off the guide cloth, and the brush of the setting machine cannot stop the normal cloth on the fuselage.


3.3 For different types of connection processing, the cloth width is 4CM apart, and the large-format connection guide cloth processing is required.


3.4 The cloth should be light-colored first and then dark brown; bleaching agent first and then extra-white, not suitable for mixing together for processing.


3.5 After the whitening is produced, the special white towel should be produced, and the bleached cloth cannot be made immediately.


3.6 Feed the cloth into the seam head, ensure that the remaining line of the seam head does not exceed 2CM, and immediately remove the road surface cloth debris and head.


3.7 When processing roll cloth or unrolling for sampling, pad the bamboo mat and apply the screw rod protection cover to avoid dirt.


3.8 Broken and dirty bamboo mats must be replaced immediately and records should be kept.


3.9 Turn off the main power switch (OFF) when the sewing machine is not needed. There is no need to put cloth bags, rags and other dirt on the cabinet table of the sewing machine.


3.10 During the whole process of manufacturing or transporting textiles, do not make any position of the human body close to the equipment or other pressure points to ensure safety; when wearing cloth or doing cleaning work, be sure to turn off the machine.


3.11 For the roll cloth, only the same processing technology can be stacked into the same roll. Its "same processing technology" means that the product names are only different in the order number, the carding processing process is the same, the secret recipe of the setting machine brush is the same, and the total width of the cloth clips is similar (the distance between them is not more than 3 cm). A maximum of 2 rolls are allowed in one roll for different processing techniques, and they are connected to each other with a 50Y guide cloth in the middle.


3.12 Pay attention to the cleanliness and maintenance of the surrounding environment during processing


surrounding natural environment).


Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU