Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

Process design, product quality analysis and control of double twist machine

Issuing time:2023-11-11 11:00


Process design, product quality analysis and control of double twist machine

Process Design and Product Quality Analysis for Double Twist Machines: A Comprehensive Guide

In order to reduce the number of knots and improve product quality, it has become a trend to replace the traditional ring ingot twist machine with double twist machine. This paper TFO Twisting machinery parts VTS08/09describes the process design and product quality analysis and control of Alma and Murata.1 x twist machine process design1. 1 ingot speedIndle speed is related to raw material. Raw material strength is high, the ingot speed can be higher. Ingot speed is related to the fineness of the yarn and the degree of twist. Generally speaking, the finer the fineness, the more the need to twist back. In order to ensure the yield, when the processing fine yarn, twist degree is high, the ingot speed is high, but the quality will become worse.1. 2 The twist degree

There are great differences between the calculated twist and the actual twist.

As can be seen from Table 1, the actual twist of the Alma double twist machine is greater than the calculated twist, and the amplitude is about 3%, but it can also be seen that this relationship is independent of the thickness of the yarn, nor of the twist degree of the yarn.1. 2. 2 Murata fold twisting machineDue to the intersection Angle, the actual winding speed is faster than the calculation speed, so the above factors must be considered in the twist setting. Murata Company gives the following twist calculation formula:


Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08

Calculate twist = design twist + design twist (co1s Q-1)×( 2)Where 1 / co s Q is the cross angle correction coefficient; 1 / 2 is the correction coefficient calculated from the observed value experiment.The calculated twist should be chosen to be larger than the design twist; i. e. multiplied by 1. 2%, 1. 6%, 2. 7% and 3. 7% respectively. If the twist is 600 / m and the crossing angle is 21 °24 ', the twist is set as follows: Calculate twist = 600 +600 (cos2 °24 ′-1)×= 622Table 2 shows the difference between the calculated twist and the actual twist when the crossover angle Q is 18 °32. According to formula (2), the theoretical difference rate should be 1. 027%, and the actual


Process Design and Product Quality Analysis for Double Twist Machines: A Comprehensive Guide

TFO Twisting machinery parts VTS08/09 The average rate of difference was 1. 029%.When the crossing angle changes and the calculated twist remains unchanged, the actual twist changes according to formula (2). Table 3 shows the variation of the actual twist of J27.8 tex 2 intersection angle, calculated at 54.5 twist / m.Table 3 J 27.8 Actual twist of tex 2 with cross angleProject design for twist / twist · m-   1Actual twist / twist · m-   1Difference rate /%18 ° 53.1 53.1 1. 026 Cross angle 22 ° 52.6 52.1 1. 044When the crossover angle is 18 °, the theoretical difference rate is 1. 027%, which is quite close to the actual difference rate of 1. 026%; when the crossover angle is 22 °, the theoretical difference rate is 1. 037%, slightly different from the actual difference rate of 1. 044%.1. 3 Overfeeding rateThe overfeeding rate depends on the hard and soft degree required by the tube. There are 11 choices for the overfeeding rate: 3%, 9%, 16%, 23%, 30%, 38%, 47%, 56%, 67%, 78% and 90%. There are three options for the overfeeding rate of Murata: 38%, 57% and 81%. The standard value of overfeeding rate of Alma is 38%, and that of Murata is 57%. When the overfeeding rate is set as the standard value, the hardness of the tube is moderate. When the small overfeed rate is selected, the winding tension is larger and the hardness of the tube is larger; otherwise, the hardness is smaller, and even can be directly used for dyeing, which facilitates dye penetration during dyeing. Generally, when dyeing cylinder, alma fold twisting machine uses 78% overfeeding rate, and 81% overfeeding rate. With the overfeeding rate of 56% and 67%, the average density of the tubes was 0. 421 and 0. 405 mg / dm, respectively3; When the overfeeding rate of Murata was 81%, the average density of the cylinder was 0. 436 mg / dm3。When the overfeeding rate is certain, other conditions are the same, the finer the fineness, the greater the hardness of the bob, therefore, when the hardness requirement of the tube is the same, the fineness is fine,

Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08/09


the general overfeeding rate is designed to be larger. Table 4 sets the overfeeding rate when the hardness of alma fold twist machine is basically close. Table 4 Set the overfeeding rate when the hardness of alma fold twist machine is basically closeThe purpose of adjusting the overfeed rate is to adjust the winding tension, and the winding tension can also be adjusted by changing the surrounding arc of the yarn on the overfeed roller. The encircling arc of yarn on the roller is achieved by changing the position of the tension guide wheel. As shown in Figure 1, the outward the tension wheel (position 1), the smaller the surrounding arc, the greater the winding tension; otherwise, the more the tension wheel is inward (position 2), the larger the surrounding arc, the smaller the winding tension. Alma fold twist machine surrounding arc adju

Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08/09

Figure 1. Regulation of the tension guide wheel1. 4 Cross angle

Cross Angle on the soft and hard degree required. Alma times twist

There are 16 °, 18 °, 20 °, 22 ° and 24 °5 species, and 4 species were 12 ° 14 ', 14 °32', 18 °08 'and 21 °24'. If the yarn is wound upForce fixed, that is, the overfeeding rate, the yarn on the surrounding arc and ingotIf the speed is equally fixed, the larger the crossing Angle, the smaller the hardness of the barrel; otherwise, the crossing Angle The smaller the tube, the harder the tube. If the double twist cylinder is a direct dyeing cylinder, generally a 22 ° and 18 °08'are 18 for Murada.1. 5 aperture heightRegulation of the air aperture height is achieved by adjusting the height of the guide yarn hook. The hook has 12 scales from small to large; the Murata fold has 8 scales from small to large from 0 to 8. The finer the yarn, the smaller the scale choice, the smaller the aperture size; on the contrary, the thicker the yarn, the larger the scale choice, the larger the aperture size. Raising the position of the guide hook will increase the size of the atmosphere and the tension and power consumption of the atmosphere. However, the position of the coil guide hook is too low, and the coil will touch the upper edge of the storage tank, which

Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08/09

is easy to scratch the yarn and cause a broken end. Therefore, as shown in Figure 2, the distance between the air coil and the upper edge of the storage tank at 15 mm is optimal.

Figure 2 Adjustment of air aperture height2 x Twist quality analysis Advantages and disadvantages of 2. 1 times Twist

Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08/09

It is generally believed that compared with the ring ingot twist machine, the double twist machine has the following advantages: it can get two twist back at the ingot, which can increase the yield per ingot; it can be directly made into a cylinder for the post process, eliminating a winding process; the wire drum, the sub coil, less internal head;
without the steel collar and wire ring, the maximum twist can reach 3 000 twist / m; the ingot speed is no longer limited by the speed of the wire coil, and the yarn can be less polluted.


The disadvantages of double machine are: large and complex structure, high cost, high


power consumption per unit output and troublesome. Use times twist


May 2010 · Volume 38 · Issue 5 Vo   38 No .5,   2010


29.5 tex 4,29.5 tex 6 and 29.5 tex 9 strands, with slightly lower fracture strength and large twist asymmetry. The comparison of the quality of circular ingot twist machine and double twist machine is shown in Table 5.As can be seen from Table 5, the difference is large; the single line fracture strength is generally decreased slightly, but the amplitude is not large; the elongation between single strong CV and fracture is basically not different.2. 2 Cause analysis2. 2. 1 times twist machine During the twist process, if each single yarn has a uniform diameter, then the twist back can be evenly distributed to the femoral line. Due to the existence of various additional uneven short fibers in the process of stretching, it is impossible to form the absolute thickness of yarn. On the twist machine, for the yarn with uneven diameter, the twist back will first reach the finer part, because the twist resistance of this part is small, after the thinner part has the twist back, the thicker part to the twist back. During the twist, the twist length of the yarn (grip length) has a great influence on the asymmetry of the twist. If the twist length is short, the twist return distribution is more uniform because it has less thin segments or even none; if the twist length is long, the twist return distribution is less uniform. Because the twist length of the double twist machine is much longer than that of the ring ingot twist machine, the twisted strands of the two models will have different twist asymmetry rate.In addition to the rolling length, the reasons include: the winding speed, the winding speed of the small end of the cone.2. 2. 2 times the twist machine yarn fracture strength is slightly lowerFor the double twist system, there are three main kinds of yarn tension: (1) traction Technical lecture31

TFO Twisting machinery parts VTS08/09Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08/09

Tension refers to the yarn tension between the parallel tube and the inlet of the upper catheter, caused by the friction of drawing the yarn from the yarn layer.(2) The coil tension is the tension of a continuous process of the yarn through the coil guide hook. The coil tension is affected by spindle speed, yarn fineness, twist and coil hook height.(3) The winding tension, unfolded between overfeeding and rolling, and reduced by overfeeding Lola. The winding tension is adjusted by changing the speed of and changing the yarn around the curve.The reason why the fracture strength of double yarn is slightly worse than that of ring ingot machine is mainly because of the tension of the above three kinds of yarn in operation, and the tension of yarn exceeds the allowable limit.2. 2. 3 times the yarn elongation rate of the twist machine is similar to the ring ingot machineOn the ring machine, the coil tension directly affects the winding tension, and the tight yarn is affected by the tensile load for a long time after twisting. In the double twist machine, the coil tension only affects the yarn in a short time. After the yarn, the original tension is greatly reduced and the yarn is coiled only by a small tension, so even if the coil tension is great in a short time, the elongation of the thread is still similar to that of the ring machine. However, if the tension of the gas aperture is unchanged, or even small, and the winding tension is not well controlled, it will affect the elongation of the femoral line, and even affect the strength. Product quality control measures for 3 times twist machineDuring the use of the double twist machine, the following measures can be taken for high quality problems such as hard tube, spider web yarn, and the broken end; reduce the yarn to reduce the overfeeding rate, reduce the winding tension, avoid the excessive tension and reduce the upper tension.
Process design, product quality analysis, double twist machine, TFO Twisting machinery parts VTS08/09


Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU