Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

The effect of combing brushes on selvages

Issuing time:2023-04-05 11:00

Damage to the tensile strength of combing and combing machine brush cleaning to the desired effect of sillicon carding

combing brush,Circular brushes,industrial brush,strip brushes,cotton comber brush

Preface:An analysis of the damage done by the tensile strength of the combing combing machine brush cleaning to the expected effect of sillin combing. The definition of the tensile strength of the combing machine brushes on the cleaning of the tinlin is clearly stated and establishedCmbing brush for NSC PB33


1 Carding machine brush 10089450.jpg mathematical class analysis method. In the HC500 type combing machine, when the combing machine brush speed is 960 r/min, 1 200 r/min, respectively, the tinlin speed is 250 clamp times / min, 300 clamp times / min, 350 clamp times / min, test the combing strip fiber length throughout and the number of cotton knots; and in the tinlin speed is 400 clamp times / min, using different combing machine brush speed. The quality of the finished yarns was checked. The test data showed that when the combing machine brush speed was expanded, the lint rate of the combed strips was reduced, the effective fibre length was increased, the number of neps and knot sizes were expanded, and the product quality standards of the key yarn segments, neps and super-strongness were further improved, while the combing machine brush speed remained constant. Keywords: Combing machine; Combing machine brush; Sillin; Cleaning tensile strength; Effective fibre length; Cotton knots

combing brush,Circular brushes,industrial brush,strip brushes,cotton comber brush

The key to the expected effect of the combing of the cotton bush by the combing machine is in the specification of the type of combing, the combing production process and the expected effect of the cleaning of the combing machine brush on the needle teeth of the combing machine. There are many experts and professors who have carried out research and tests on the specification parameters of the tinlin teeth such as the working angle, density, height and the relationship between the carding surface and the expected effect of the carding, providing the basic theoretical basis for the design of the tinlin scheme for the combing machine. There are also experts and professors from the qualitative analysis of combing small rolls, feeding lengths, drop spacing, carding spacing and the opening and closing of the clamp plate timed restart to explore the damage of the combing machine to the expected effect of the tin combing, in order to solve the professional difficulties in the configuration of the combing production process parameters and the movement of the important parts of the combing machine fitness in conjunction with each other. However, there is a lack of specialised scientific research and analysis of the damage to textile quality caused by the expected effect of the cleaning of the combing machine brushes. In order to better be able to better scientific research combing machine brush speed on the cleaning expected effect of the tinlin needle teeth, the group established the mathematical class analysis method of the cleaning tensile strength of the combing machine brush on the tinlin needle teeth, and the combing machine brush


202231Note: Ren Jiazhi ( 1959-) , Male, Authoritative Expert, Zhengzhou, 450007 Received:2012-12-03


The expected effect of combing and the quality of textiles at different combing machine brushes and tinlin speeds were analysed experimentally.


1 Analysis of the cleaning tensile strength of the combing machine brushes against the needle teeth of the tinlin


1.1 Position of the combing machine brush in relation to the tinlin

combing brush,Circular brushes,industrial brush,strip brushes,cotton comber brush

In the combing machine, the position relationship between the sillings, the combing machine brush and the triangular airflow plate is shown in Figure 1 below. In the work of the combing machine, because the density and surface line speed of the combing machine brush brown sheet are beyond the tin forest, and the combing machine brush in the installation of brown sheet multi-faceted tin forest needle teeth deep level for 1 mm ~ 2 mm, so the combing machine brush brown sheet can immediately clean the surface of the tin forest needle teeth cotton knots, slag and short lint, and by the partition below the suction vent suction away and into the combing drop cotton. In the case that the particle size distribution, density, plasticity and installation position of the combing machine brush is always the same, the combing machine brush can clean up the expected effect on the needle teeth of the tin woods, and the relative speed of the combing machine brush and the tin woods.


1.2 Tensile strength of the combing machine brushes for the cleaning of the needle teeth of the cylinder


In order to be able to better analyse the expected effect of the combing machine brush on the cleaning of the selvage needle teeth, the group introduces the definition of the cleaning tensile strength, defining the average yarn count of each selvage needle tooth touched by the selvage brush during a working cycle of the combing machine as the cleaning tensile strength.


The average yarn count is called the cleaning tensile strength.


If n1 is the combing machine brush speed (r/min) and n2 is the tinlin speed (clamp/min), then the angular speed of the combing machine brush and tinlin rotation ω1, ω2


(slope/s) are respectively .


2πn1


ω1 =( 1)


60


2πn2


ω2 =( 2)


60


Let θ be the angle (°) between the first and last rows of needles of the celing, called the angle of the celing motor shaft, then the time t required for the celing to flip the angle θ is.


πθθ


t==( 3)


180ω26×n2


Let r1 be the radius of gyration of the combing machine brush (mm), then the chord length S1 of the combing machine brush flipping in time t is.


πθr1n1


s1 =ω1×t×r1 =( 4)


180n2


Z1 and Z2 are the total number of yarn counts (rows) and the total number of teeth (teeth) of the combing machine brushes, respectively.


Z1θn1Z1


m1 = × s1 = ( 5) The tensile strength of the combing machine brushes against (2πr1) sillin teeth (360n2) for cleaning P (roots/tooth) is.


m1θ n1 Z1


P==××( 6)


Z2360 n2 Z2


2 combing machine brushes 10089450.jpg from the formula ( 6) is known, combing machine brushes to the sillin needle teeth cleaning tensile strength P with the combing machine brush speed, combing machine brushes the total yarn count, sillin motor shaft angle correlation, with sillin speed, sillin total number of teeth inverse proportion.


Cmbing brush for NSC p100When spinning fine lint cotton, using the Dutch Schiesser Schiesser, the angle of the Schiesser motor shaft θ is 90°, the total number of teeth of the Schiesser Z2 is 29 112 teeth, the total yarn count of the combing machine brush is 200 000 yarn pieces Z1, at the combing machine brush speed n1 is 960 r/min, the Schiesser speed n2 is 250 pincers/min, 300 pincers/min, 350 pincers/min, 400 pincers/min, respectively. When n1 is 1 200 r/min and n2 is 250, 300, 350 and 400 jaws/min respectively, the tensile strength of the combing brushes against the needle teeth is calculated according to equation ( 6) as 6. 60 teeth/tooth, 5. 49 teeth/tooth, 4. 71 teeth/tooth and 4. 12 teeth/tooth respectively; when n1 is 1 200 r/min and n2 is 250 jaws/min, 300 jaws/min, 350 jaws/min and 400 jaws/min respectively, the tensile strength of the combing brushes against the needle teeth is calculated as P The P values are 8. 24 teeth, 6. 87 teeth, 5. 88 teeth and 5. 15 teeth respectively. As can be seen from the above values, at a combing brush speed of 960 r/min, the speed of the cylinder increases from 300 jaws/min to


The cleaning tensile strength P decreases from 5. 49 teeth/tooth to 4. 12 teeth/tooth, a reduction of 25%. Therefore, in addition to the increased speed of the combing machine, it is necessary to increase the speed of the combing machine brushes or to use a high relative density of combing machine brushes if the desired effect of the combing machine brushes on the removal of the tinwood is to be guaranteed.


2 Test


2.1 Test specification


A JC 9.7 tex combed yarn was spun from Xinjiang cotton of class 3, hand-tied length 29 mm, Machron number 4.6, 12.7 mm staple rate 14.4%. The basic parameters of the combing production process are: 61. 03 g/5 m qualitative analysis of the small rolls, backward feeding of the cotton, 4. 3 mm feed length, 37 detection range of the selvedge, 0. 5 mm top comb insertion to the deep level, 10 mm drop spacing, 22. 07 g/5 m qualitative analysis of the combing strips, 19% combing drop rate.


2.2 Test programme


In the HC500 combing machine, the effective fibre length, the lint rate, the number of knots and the type of knots in the combed strips were checked with a PREMIER aQuar NL checker at a combing brush speed n1 of 960 r/min and 1 200 r/min and a cylinder speed n2 of 250 clamps/min, 300 clamps/min and 350 clamps/min, respectively. The data are analysed statistically.


In order to better detect the damage to textile quality caused by the high combing speed of the HC500 combing machine, a SL100A dryness checker was used to check the CV of the finished yarn and recurrent yarn defects at n2 of 400 clamps/min and n1 of 960 r/min and 1 200 r/min, respectively. Combing machine brushes


With 400 clamps/min and other production specifications remaining unchanged, the combing machine brush speed was increased from 960 r/min to 1 200 r/min, resulting in a 39. 5% reduction in critical yarn formation, an 18. 3% reduction in neps, and a significant increase in yarn dryness CV, coarse knots and split superelevation, but some deterioration in yarn superelevation CV and hairiness index H.

combing brush,Circular brushes,industrial brush,strip brushes,cotton comber brush

3. 3 Comprehensive analysis


In addition to the different combing machine brush speeds, it is known from the test results of the fibre length of the combed strips, the number of knots, the type of knot specifications and the quality standards of the finished yarn products that the expansion of the combing machine brush speed enhances the expected effect of the combing machine brush on the cleaning of the needle teeth of the selenium, enhances the expected effect of the elimination of the polyester staple fibre dimension in the whole process of selenium carding, increases the effective fibre length of the combed strips and thus significantly


The effective fibre length, the 12. 7 mm lint rate and the neps in 1 gram of combed strip were measured at different combing machine brush and cylinder speeds. The reason for this is that as the speed of the combing machine increases, the tensile strength of the combing machine brushes to clean up the needle teeth of the combing machine decreases, the cleanliness level of the combing surface decreases, and the professional ability of the combing machine to eliminate short staples is reduced during the next cycle of combing, in addition to making the combing process more hazardous for synthetic fibres. The reduction of yarn slubs, critical links and knots improves yarn dryness CV and super super strength. The expansion of the combing machine brush speed leads to an increase in the number of times the combing machine brush touches the selvage needle teeth and an increase in the chance of the combing machine brush rubbing the synthetic fibres, as well as an increase in the chance of the combing machine brush rewinding, which leads to an increase in the number of neps and an increase in the size of the neps in the combed strips; however, the neps in the finished yarn increase with the increase in the number of neps in the combed strips and decrease with the decrease in the short staple rate in the combed strips. Therefore, the yarn knots ultimately depend on the level of increase in the number of knots in the combed sliver and the lint rate.


4 Results


( 1) The tensile strength of the combing machine brushes for cleaning of the selvage needle teeth is related to the combing machine brush speed, the total yarn count of the combing machine brushes and the angle of the selvage motor shaft, and is inversely proportional to the selvage speed and the total number of selvage teeth.


( 2) By increasing the combing machine brush speed, the short staple rate in the combed strip decreases, the effective fibre length expands, the number of neps increases and the size of neps expands.

combing brush,Circular brushes,industrial brush,strip brushes,cotton comber brush

( 3) In the HC500 combing machine, when the cylinder speed is


( 3) In the HC500 combing machine, the combing brush speed is adjusted from 960 r/min to 1 200 r/min at a speed of 400 clamps/min, which improves yarn quality.


Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU