Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

Textile Combing 100 Questions(3)

Issuing time:2022-05-07 11:00

How to ensure the uniformity of combing noil rate?


Answer: The factors that endanger the noil rate:

cotton comber brush,combing brush,Circular brushes,industrial brush,strip brushes

(1) The preparation of raw cotton fluctuates greatly.


(2) The foremost part of the nipper is walking.


(3) The bow-shaped plate is precisely positioned for walking.


(4) The bow-shaped plate is precisely positioned, the separated roller rotates on time, and the nipper plate is closed on time. The main parameters of the three major processing processes do not cooperate well with each other.


(5) The top comb gauge and the cylinder finishing gauge change.


(6) Flowers are hung in the main air duct, and the negative pressure changes greatly.


(7) Too much miscellaneous cotton is impinged on the upper and lower jaw lips of the nipper.


(8) The temperature and humidity change greatly.

cotton comber brush,combing brush,Circular brushes,industrial brush,strip brushes

202231Countermeasures: On the basis of doing a good job of unifying the noil gap, the height of the top comb, the clearance of the cylinder, and the positioning of the front map of the nipper, adjust the noil gap, and then ensure the uniformity of the noil rate. .


Question 17


How to improve combed evenness?


Answer: The countermeasures to improve the level of combed evenness probably have the following levels:


1. Maintain a stable micro-roll configuration.


2. The nippers of the comber are opened and closed on time, and the bow plates are accurately positioned, and the separated rollers are rotated (reversely) on time and effectively and accurately positioned: ① When the nippers that cooperate with each other are properly closed, the cylinder should be When a row of combing needles is located under the tong lip, the even teeth of the left and right tong lips can reasonably improve the evenness, and the chemical fibers in the combing bar are relatively reduced; ② The precise positioning of the bow plate should be integrated into the timing of the tong plate closing and closing. After the delay time, the provisions for grasping and combing can be reasonably carried out. If the bow plate is too backward, the comb needles in the rear seat of the cylinder will touch the chemical fibers at the tail of the separated clump when they are at the tightest part of the surface of the separated roller, which is very easy for the cylinder comb needles to catch the chemical fibers and cause falling. Increased long chemical fibers in cotton and noil. ③ Effectively adjust to clockwise rotation.


3. The eccentricity of the short shaft pin of the front inner diameter gauge should be 70mm.


4. Effectively distribute each part of the support force to separate yarns, and the cotton feeding support force is slightly larger at 1.05 to 1.09; the support force of the cabinet table and the support force between the separated rollers are properly equipped, which is not suitable for too large; the diameter of the bell mouth stage is reasonably arranged , avoid shaving.


5. Everything is normal to separate out the glue stick and divide the yarn and pressurize it, and maintain a moderate roller gap.


6. Machines and equipment use a large number of combinations.


Question 18


How is the application cycle time of a combed brush determined? Why is the comber brush not clean?


Answer: After the comber brush is used for a period of time, there will be uneven brown hair and other conditions, which will immediately endanger the cleaning work of the cylinder 2 comber brush 10089450.jpg. When the condition of good and bad occurs, the brush needs to be replaced regularly. The diameter of the brush is less than 80mm, and the distance between the brush and the cylinder shell is more than 17mm, and it cannot be used.

cotton comber brush,combing brush,Circular brushes,industrial brush,strip brushes

To increase the application cycle time of the brush, it is necessary to choose a brush made of high quality brown bristles and maintain the operation condition of the brush regularly. Taicang Zhenyu Textile Equipment Co., Ltd. is a manufacturer of combing machine brushes, brush rollers, cleaning brushes, nylon needle cores for needle-carding machines, various textile accessories and textile brushes. It has 15 years of experience in brush production. 13 years of experience in brush customization solutions, consultation phone: 18962318500


Question 19


How to analyze the spectrogram of the comber?


Answer: There are two kinds of abnormality in Rauschenberg, one is the mechanical wave and the other is the yarn separation wave. It often occurs at 8cm, 10cm, 14cm, 16cm, 20cm, 40cm to 60cm, and up to one meter. Under normal circumstances, the yarn splitting wave occurs before 20 centimeters, the 40 to 60 part is called the steel lap wave, and the one meter up and down may be the coil wave. Comber brush


From the analysis of the authoritative experts of the USTER levelness tester, it is necessary to analyze the yarn separation wave from the quality of the top roller, the gripping force with the roller and the rationalization of the yarn separation distance. If the mechanical wave occurred 20 cm ago, it is necessary to check whether the roller is less oily, bent, and whether the timing belt is not tight and loose. The parts from 40 to 60 are generally caused by the overlapping of steel bars, and sometimes the different sizes of the incoming air will also cause mechanical waves. It is necessary to check whether part of the sliver safety channel, the quality of the can and the eccentricity of the left and right coils are valid.


Question 20


How to balance noil rate and yarn quality?


A: Rieter companies have an opinion on the zero-point of combing noil rate. They feel that the zero-point of the raw material is different depending on the short-staple content. In general, when the noil rate is increased, the improvement of the yarn quality is also linearly related. When the noil rate increases to a certain standard value, it will reach the zero point. Even if the noil rate is further increased, the improvement of the yarn quality will not It is not large, so this provides a theoretical source for the adjustment of the noil rate in the future. We can finally determine the noil rate according to the experiment of the addition and subtraction of the yarn quality within ten. Comber brush


Expert and professor Ren Jiazhi clearly put forward the opinion of whether combing is too much with the amount of short staples: that is, the short staple content caused by damage to chemical fibers in the finishing = the short staple content in the waste cotton The short staple content in the combed sliver - cotton Rolls contain short pile. If the sum of the short staple content in the noil and202231 the short staple content in the combed sliver far exceeds the short staple contained in the cotton lap, it indicates that the combing is too much damage to the chemical fiber. The main parameters of the machining process of the machine operation, showing the relative value of the theoretical source, to obtain customer satisfaction with the least cost.


USTER has clearly put forward the opinion of precise positioning of product quality: the USTER government reports that 5% of the products are of good quality, but the price is high, and the USTER government reports that 95% of the products have a strong price advantage. She feels: According to the requirements of customers, select effective cotton blending and on-machine operation and processing technology, with the least operating and management costs, to maximize economic benefits and profits.

cotton comber brush,combing brush,Circular brushes,industrial brush,strip brushes

Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU