Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

Textile Combing 100 Questions(1)

Issuing time:2022-04-30 11:00

1. What are the reasons for the poor cotton web of the comber?   wool tops


A: Cmbing brush for NSC p100The most common problem in the comber is the poor cotton web. There are many reasons for the poor cotton web. Most of the common problems will damage the quality of the cotton web.wool tops


Poor web formation (poor gap junctions and fish scale spots) causes:


1. Separation Roller clockwise timing is performed too early or too late.


2. Separated Roller Sports Fitness and Clamp Sports Fitness to cooperate with each other to perform regular walks.wool tops

wool tops,combing brush,Circular brushes,industrial brush

3. The cotton net is too strong.


4. The precise positioning of the cylinder bow is outdated, and the last row of combs is aimed at the harm of pouring into the fuselage fiber bundle.


5. The top comb is timed or spaced.


When the cotton web is not well combined, when the combing sliver is checked for evenness, there will be a combination wave. When the situation is serious, it can be seen that there are obvious horizontal and vertical marks on the edge of the cotton web. The timing of the separated roller is too early. When the steel bars are connected, the back-end engineer of the cotton mesh in the previous clamp and the cotton mesh in the latter clamp overlap, and there are synthetic fibers that are bent and hooked. If the timing of the separated roller is too late, the cotton web poured into the shell will be taken away by the cylinder, and there is often no cotton web in the middle of the machine, and the long synthetic fibers in the waste continue to grow.wool tops

wool tops,combing brush,Circular brushes,industrial brush

梳毛机毛刷辊.pngCauses of rotten holes in cotton nets:


1. Too many cotton bundles embedded in the cylinder.


2. The timing of the nipper is performed too early (ie, the mouth is opened too late).


3. A part of the excavation of the separated roller groove is too bent.


4. The separated top roller is bent, dented or the diameter is too small and the plasticity is insufficient.


5. The air flow double arc plate is too high and far away from the soft brush.


6. The pressure spring of the nipper is cracked, or the pressure is insufficient.


7. Separate out the roller or separate out a part of the top roller to wrap around the flower.


The reasons for the poor picture quality of the cotton net:


1. The nipper opens its mouth very late, and the top comb function is not fully utilized.


2. Cylinder needles are too harmful.


3. Too much cylinder intarsia and not enough grooming.


4. The top comb is impacted by synthetic fibers, sediment or broken needles, missing needles, and too many needles.


5. The upper and lower nipper plates are unevenly grasped, the nipper plate is filled with yellow cracks or the shaft is impacted and dirty.

wool tops

6. Cylinder combs have very large gaps.


7. The nipper and the separated top roller are stuttered.


8. The air flow double arc plate has a very large distance from the soft brush.


9. The diameter of the separated top roller is not large or the compressive strength of the top roller is too high and has no plasticity.


Reasons for poor production and processing of cotton web edges:


1. The metal surface of the top roller is not properly solved or the surface is bumped and rough.


2. Comb needles on both sides of the cylinder are more harmful.


3. The diameter of the separated top roller is not large and the plasticity is insufficient.


4. The separated roller collector hook is not open or very large, and the high and low parts are out of alignment.


5. Fan or gross speed is too fast.


6. The relative humidity of the production line air is too high or too low.


7. The sway bar bracket part is forward.


8. The airflow double arc plate touches the soft brush too deeply.

wool tops

The reason why the cotton mesh is cut across is:


1. Position the top position of the forceps cotton to move around.


2. The top comb is precisely positioned for walking or the top comb is too deep.


3. Some traverses are broken to support the teeth of the cotton roller.


2. When spinning Xinjiang long-staple cotton for 80s, when the speed of E65 is above 400 nips/min, there are serious edge breakage and cloud spots. How to adjust the production process to solve this problem?


Answer: There are many factors that damage the quality of the cotton web. It should be adjusted comprehensively from the past to the back: at the beginning, adjust the edge of the small roll to ensure the high quality of the small roll structure, and adjust the negative working pressure of the combing machine noil to ensure the high quality of the small roll. High, the output cotton layer of the combed cotton web is not easy to be too thin, and the qualitative analysis of small rolls can be improved by appropriate improvement. Changing to forward feeding can also improve lap breakage. Reasonably formulate the timing of the separated rollers, and the timing is too late or the speed of the soft brush is too high, which may easily cause cloud spots on the cotton web.

wool tops,combing brush,Circular brushes,industrial brush

3. What are the reasons for the overflow of kitchen countertops?

wool tops

Pin strips

Answer: 1. The temperature and humidity of the combing room have changed. 2. The rotation of the rear yarn splitting roller is inflexible. 3. The noil rate has changed. 4. The bell mouth stage of the car surface, the rear roller teeth or the bearing teeth of the kitchen countertop do not meet the production process requirements. 5. Check whether the clutch of the calender roll clutch is smooth, and adjust it according to the requirements. If it is an old-fashioned combing machine, please check whether the inner diameter of the overflow valve plate of the pusher cylinder is too small, whether the filter system is blocked, and the sealing ring of the pusher cylinder Whether it is aging, worn, and leaking, and whether the pressure of the gas pipeline is too low.


4. What is the reason for the sticky roll of combed small rolls?


Answer: The small paper strips or the guide columns on both sides of the cotton layer for the combing preparation process, the slitter, the feeding baffle, the cotton collector, the curved guide plate, the sliver uniform machine equipment and the chuck parts are correct. The sticky roll damage is very large, and it requires standardization. The feeding and output of the sliver should be arranged symmetrically and evenly. , the parts of the chuck and the bobbin are not standardized, which will cause the broken edge of the small roll to slowly expand to the middle when unwinding, resulting in serious sticky rolls.

wool tops,combing brush,Circular brushes,industrial brush

In addition, if the pressure on the coil is too high or too small, it will all lead to the poor forming of small rolls. If the pressure is too large, it will damage the structure of the cotton layer and it is easy to stick to the roll. Raw materials and cotton blends have a certain level of damage to small rolls, especially when imported cotton and high-sugar raw materials are used, such as African cotton. In terms of cotton blending, it is necessary to use high-sugar raw materials with a low occupancy rate, or to de-sugar the raw materials. The comber requires the control of temperature and environmental humidity. Generally, the temperature is controlled at 25±3 °C, and the relative air humidity is 50%~ 60% in the middle is appropriate.


5. What is the reason for the poor consistency of combing noil rate?

wool tops

Answer: (1) The raw cotton configuration fluctuates greatly. (2) The foremost part of the nipper moves. (3) The bow plate is precisely positioned and moved. (4) The bow-shaped plate is precisely positioned, the separated rollers are rotated in a timely manner, and the nipper plate is closed and closed regularly. The three basic parameters of the production process are not properly coordinated with each other. (5) Top comb gauge, cylinder comb gauge change. (6) The main ventilation duct is hung with flowers, and the negative working pressure varies greatly. (7) There are too many impurities on the pliers plate and the lower pliers lip. (8) The temperature and humidity vary greatly.



Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU