Suzhou Yuedar Textile Machinery Co., Ltd.
Product  Brush ,Textile Machinery  Spare Parts

Dynamic and Static Finite Element Analysis of the Comb Box of the Needle-Carding Machine

Issuing time:2022-04-13 11:00

The comb box of the needle carding machine is an important basic part of the needle carding machine. Its dynamic and static

pinned inserts


The characteristics affect the working performance of the whole machine of the needle carding machine.pinned inserts针壳-(6).jpg

The ligands are subjected to static strength and modal analysis to obtain the overall performance. Such as

As shown in Figure 1 (the side of the gear shown is the rear side of the comb box), the comb box assembly

Mainly composed of upper and lower boxes, guide rails, needle plates, cam beaters, 8 screws and

8 baffles and other parts. When working, the motion and power are driven by the input shaft

At the same time, it is transmitted to the bottom 2 screws, and the screws drive the needle plate to feed the tops.pinned inserts

Carding is carried out, and the needle plate is supported on the guide rail for circular motion. Comb box size

is 315 mm × 430 mm × 345 mm, and the lid size is 355

mm × 490 mm × 67 mm, with a minimum wall thickness of 6 mm. comb

The overall force of the box is small, but the wall thickness of the box, the distance between the bearing holes and the length of the box

The size of the bearing directly affects the installation position of the bearing and the screw, and the space between the upper and lower guide rails.

The distance and working range will affect the working performance of the comb box, so the comb box should be

GILL BOX BRUSHFinite Element Analysis.pinned inserts

Use UG to complete the modeling and import it into ANSYS for analysis. mold

The type belongs to a large-scale finite element analysis project, with various and complex sizes.

The number of cells divided by the grid is huge, so the grouping of the assembly

The components are processed as necessary on the basis of not affecting the analysis to ensure that

Leave the upper and lower box bodies, 4 screws, upper box cover and guide rails, the materials are respectively

Yes: Comb box ZG20, guide rail and screw are 20CrMo, elastic modulus

E137GPa, Poisson's ratio 0.3, Block Lanczos meshing the model

The result is shown in Figure 2.pinned inserts

The Block Lanczos method is suitable for finding the eigenvalues of large symmetric matrices

GILL BOX BRUSHSolve the problem, best suited for models consisting of shells or shells and solids, the method

The accuracy is the same as the Subspace method, the convergence speed is faster, but it requires more

Subspace method memory is about 50% more. The Block Lanczos method uses dilute

Sparse matrix equation solver.

The first 8 orders of modal extraction, and the first 8 orders of extended modal extraction.

Static Analysis

The motor power of the comb box assembly is 2.2 kW, the input shaft (see fig.

1) Input speed: the first gear is 348.54 r/min, the second gear is 348.54 r/min

279.54 r/min, obviously the load is large in the first gear, so only the first gear needs to be analyzed

working condition. The load is applied to the bearing seat hole of the box mounting screw,

The shaft bore mainly bears radial force, at the two input screws, in addition to the radial force

force, and axial force; according to the simulation analysis results of the comb box, each axis is obtained.pinned inserts

pin stripsForce at the bearing hole. The static analysis results of the first gear are shown in Fig. 11.

The figure indicates the maximum stress position of the box. The results show that when the needle

The largest Von on the comb box assembly when the comb is operating at first speed

Misses stress is about 27 MPa, located in the mounting hole of the lower left box

, the mechanical properties of material ZG20: yield strength σs = 235 MPa,

Can meet the strength requirements.

concluding remarkspin strips

The vibration of the comb box assembly can be expressed as a linear combination of natural modes of each order. The low-order natural mode has a greater impact on the vibration of the comb box than the high-order, and the lower the order, the greater the impact on the comb box. Dynamic characteristics play a decisive role. First-order mode natural vibration frequency of comb box assembly

The rate is 234.979 Hz, which is the vertical swing of the assembly

The amplitude of the front side of the upper box cover of the assembly is the largest, and the mode shape of the assembly is basically

symmetry. The frequency of the first-order main mode is much higher than its operating frequency, so the

Take measures to appropriately increase the wall thickness of the box to avoid resonance near the first-order main mode frequency of the comb box of the needle-comb machine.pin strips

The driving power of the needle-carding machine is small, and the force on the comb box is small. According to the static analysis, the strength is sufficient. Therefore, the influence of friction and speed on it is mainly considered in the design.

pin strips



Share to:
About us We product wide range of brushes for the textile industry, in particular for combing wool and cotton, in many versions and sizes for NSC Schlumberger, Rieter and Sant’Andrea machines.The various models are made of Natural or Extrastiff Tampico and also Nylon, as well as a wide range of accessories, such as strips in bristle, horsehair, goat hair and nylon.
Press-in Strips in all sizes for different NSC, COGNETEX, ST. ANDREA , OKK , etc. Gill Boxes.
High Quality Press-in Pin strips in all sizes for NSC GN/GC /GV Gill Boxes, COGNETEX, OKK, SANT ANDREA & for other makes on request.
Contact us
Contact email:market@ydrtexm.com
Contact phone :+8618015626503
Whatsapp:8618015626503
Contact address: CHINA SUZHOU city, JIANGSU