The needle carding process is an important process in the wool spinning process. Its function is to mix the raw tops in a certain proportion, combine, draw, and comb through several passes, and further remove impurities, and process them into cooked tops that meet the requirements for the next process. use. The quality of the tops on the bottom of the needle carding machine directly affects the quality of roving and spun yarn in the subsequent process, faller barsso it is very important to control the quality of the tops on the bottom of the needle carding machine. Now from the following aspects, we will analyze how to improve the quality of the bottom top of the needle carding machine.GILL BOX
1 Reasonable selection of process parameters 1.1 Front gauge A Front gauge is the distance from the first needle plate of the pointer card to the jaw of the drafting roller. The front gauge A should be based on half of the average fiber length (mite value), And add or subtract 5 mm of adjustment to achieve the best CV% value. i.e. A= . For mixed sliver and double combing back-end combing machine, A= should be selected;
faller bars
1.2 Draft ratio After a large number of tests, it has been proved that the draft ratio GILL BOXis higher than 8 or lower than 6, which is easy to cause unevenness. Therefore, if possible, the draft ratio should preferably be set between 6 and 8. 1.3 Selection of Feeding Amount Too large (≥250 g/m) or too small (≤120 g/m) of feed will affect the evenness of the tops on the lower machine, which will easily cause unevenness. A good choice is in t
he range of 160 to 240 g/m. For the third-pass needle-GILL BOXcarding machine, since the slitter occupies a larger space in the feeding area and requires lighter tops on the lower machine, the feeding amount can be appropriately reduced. 1.4 The number of combined roots Theoretically, the combination and combination of tops play a role in leveling, and the more the number of combined roots, the better the leveling effect. However, the number of combs is often restricted by factors such as the top weight and output of each line of needles. Therefore, under the conditions allowed by the process, the number of combinations of each line of needles should be increased as much as possible to achieve the best CV% value. 1.5 The pressure adjustment range of the drafting rubber roller is 200-400 kg. If the pressure is too small, the sliver will not be drawn, and the phenomenon of "pulling sheepskin" will appear. If the pressure is too high, it will cause damage to the fiber and increase the The operating load of the machine affects the evenness quality.faller bars
The correct pressure of the drafting rubber roller should be the pressure under the condition that the sliver can be drafted.GILL BOX,Press-in Strips
1.6 Feeding and output tension of tops The unsuitable feeding and output tensions of tops are a common cause of poor top quality. The control criterion of the feeding top tension is to ensure that the sliver is straight and without curling, the tension should be as small as possible or the sliver is "relaxed". The spectrogram shows uneven defects in the range of 25 to 30 cm; if the tension of the strip is too tight, there will be uneven defects of 5 to 10 cm with smaller segments, and the tension between the front roller and the coiler roller It should be ensured that the sliver is not too slack within this range; finally, the top tension (pre-drafting)GILL BOX
between the feed roller and the needle plate should be considered. Unexpected draft of the sliver. In general, the proper tension between the back roller and the throat plate can be felt by pressing the top with your hand from above. The above process parameters are not static for different raw material varieties, and the technicians should make appropriate adjustments according to the different raw materials to make the sliver reach the best CV% value. 2 Ensure that the main process parts of the machine areGILL BOX in normal operation. Mechanical problems involve all the parts on a machine. A good technician should be familiar with the transmission diagram of the machine and accurately understand the function of each part. Often, individual components are worn, deformed or damaged, and the machine will continue to operate, but will affect the quality of the sliver and increase the CV% value. The focus here is to analyze the influence of the main process components of the needle carding machine on the evenness quality. 2.1 Needle plates, screws, Press-in Stripsguide rails and beater boards should always be kept in good condition, blunt needles, bent needles, missing needles, worn needle strips, worn or broken needle plate seats, and worn needle plate beaters, and the striking time is not long. Correct, the guide rail is worn and loose, the needle is dirty, the screw falls off, the screw is out of oil, the front plate of the needle plate is worn, and the needle plate guide is lost, all of which will affect the movement of the needle plate and increase the unevenness of the top. rate value. Therefore, these parts should be checked and refueled regularly. But be sure to pay attention not to add too much oil to the needle plate and the screw part, otherwise the oil will seep into the area of the comb needle that is in contact with the top, causing the needle plate to wrap around and the needle plate to jam.GILL BOX faller bars
2.2 Drafting mechanism The drafting mechanism is composed of large and small rollers, rubber rollers, transmission shafts, bearings and transmission gears, which should always be in good condition. These parts should be checked and refueled regularly, and should be done in sequence: ① Rubber wrapping of the rubber rollers The thickness of the coating should be at least 8 mm, the coating should have good surface quality, no knife marks and scratches, dents and flat indentations, and moderate hardness (Shore hardness 80°). Press-in StripsAfter long-faller barsterm use, the surface of the skin roller will become very smooth and lose the ability to hold the fibers, then a skin roller is required. ②The operation of the large roller should be flexible, the groove on the surface of the roller should be in good condition, there should be no scratches or abrasions, and there should be no dirt in the groove to avoid entanglement; the key of the roller shaft should be closely matched with the keyway and cannot be loosened , because the roller acts as the main drive. ③ The small roller is very important for the ideal holding of the fiber. The gear transmission system of the small roller should be in good condition, and the surface speed of the small roller should be exactly the same as the surface speed of the large roller and the top roller. In any case, if the unit composed of two rollers and top rollers does not work properly, a chimney of about 20 cm will be generated on the spectrogram. This group of drafting mechanism is the core part of the needle carding machine, which completes 90% of the workload of drafting and carding, which should be paid attention to. 2.3 Slitters First, the surface finish of the slitters should be ensured, and the width between the slits should be appropriate. The width between the rear slitters is at least about 15 cm (the output sliver is 1),Press-in Strips too narrow will lead to accelerated wear of the top rollers and lead to uneven drafting; the f
unction of the front slitter is to control the top after being drawn. When leaving the drafting roller, just touch the edge of the moving fibers for good fiber control and reduce entanglement of the rollers and cots. 2.4 Coiler Coiler is an important part of the needle carding machine. The surface of the upper coiler and the bottom surface of the coiler should be smooth and free of burrs, and the two rollers should be parallel. At the same time, ensure that the pressure of the two rollers is correct. , In addition, the nylon gears, steel wire raceways and balls in the coiler should be checked frequently for wear. Note that when replacing the balls, all the balls must be replaced at the same time and ensure that the diameter of the balls is within 9.525±0.0005 mm. Press-in StripsReplace one or more balls and install balls with poor diameter. In addition to the many factors mentioned above, the quality of the tops in the previous process of the needle-carding machine has a direct impact on the quality of the tops under the needle-carding machine. In addition, reasonable workshop temperature and humidity also play an important role in ensuring the evenness quality of tops. 3 Conclusions In order to improve the quality of the tops on the lower machine of the needle carding machine, on the premise that the raw materials and the temperature and humidity of the workshop meet the requirements, according to the different types of raw materials, the process parameters of each line of needle carding should be reasonably selected, and the equipment, especially the main process components, should operate normally. is critical. Only in this way can high-quality tops be produced, providing high-quality raw materials for roving, spinning and other processes.faller bars